Rikon Power Tools 23-400H Instrukcja Właściciela

23-400Hwww.rikontools.com23-400HM116” Thickness Planer with Helical CutterheadOperator’s ManualRecord the serial number and date of purchase in your m

10OPERATIONPLANER TABLE HEIGHT ADJUSTMENTThe Hand Wheel controls the height setting for the planer's bed and the final planed thickness of your l

OPERATION11PLANER OPERATIONBefore turning on the planer, review the safety precau-tions listed on pages 3 to 6, and the operating instruc-tions on pag

12ADJUSTMENTSROTATING OR REPLACING KNIFE INSERTSThis machine has a helical cutterhead with four rows of carbide knife inserts. Each of the 72 inserts

13ADJUSTMENTSFIG. 17Planer Table Alignment continued from page 121. Make sure that the planer/jointer's switch is turned off, and the plug is dis

14ADJUSTMENTSADJUSTING THE CUTTERHEADThe Cutterhead that holds the knife inserts is fastened to the machine's cabinet, and is not adjustable. Bas

15ADJUSTMENTSADJUSTING DRIVE BELTSThe cutterhead drive belt and the feedgear drive belt need to be checked periodically and retightened if neces-sary.

16ADJUSTMENTSFIG. 2710. When all belts have been checked and any mainten-ace has been done, replace and secure the side panel and speed control knob b

17MAINTENANCE1. Before each use:- Check the power cord and plug for any wear or damage.- Check for any loose screws or hardware.- Check the area t

18TROUBLESHOOTINGSYMPTOM POSSIBLE CAUSES SOLUTIONSPlaner will not start.1. No power2. Blown fuse3. Main on/off switch or Micro switch in cover is

414243444546474849505152P23-400-41P23-400-42P23-400-43P23-400-44P23-400-45P23-400-46P23-400-47P23-400-48P23-400-49P23-400-50P23-400-51P23-400-52Flat W

2TABLE OF CONTENTSSPECIFICATIONSNOTE: The specications, photographs, drawings and information in this manual represent the current model when the man

20PARTS DIAGRAMTABLE ASSEMBLY

21PARTS LISTFlat Washer 8Hex Nut M6Screw M6x12Thickness TableIndicatorScaleLock HandleHex Nut M10Locking BarSet Screw M8x16Crank Ha

22PARTS DIAGRAMPARTS DIAGRAMMOTOR & DRIVE SYSTEM

23PARTS LISTKEY NO.MFG. PART NO.NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts.For Parts under Warranty, the

24PARTS DIAGRAMCABINET & CONTROLS

25PARTS LISTKEY NO. MFG. PART NO.NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts.For Parts under Warranty, th

26WARRANTYWARRANTYWARRANTYWARRANTY

27NOTESUse this section to record maintenance, service and any calls to Technical Support:

www.rikontools.com23-400HM123-400HFor more information:16 Progress RdBillerica, MA 01821877-884-5167 / [email protected]

3SAFETY SYMBOLSIMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be

4SAFETY INSTRUCTIONS 16. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to the “OFF” p

5 THIS SYMBOL DESIGNATES THAT THIS TOOL IS LISTED BY THE INTERTEK TESTING SER-VICES, TO UNITED STATES AND CANADIAN STANDARD

6SPECIFIC SAFETY INSTRUCTIONS FOR PLANERSSAVE THESE INSTRUCTIONS.Refer to them often. 1. Do not operate this machine until you have read all of the

7GETTING TO KNOW YOUR MACHINECarefully unpack your planer from its carton. Check for any shipping damage, and make sure the following parts are includ

8ASSEMBLY THE PLANER MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE.Un

9ASSEMBLYINSTALLING DUST HOSEIt is extremely important that a dust collection system is used with this planer to eliminate harmful airborne dust, prev